20 designs · 2 Pro
Motion & Tactile
20 DIY sim racing motion & tactile designs you build yourself: 2 Pro designs on Patreon and 18 free, each with build notes. Most built: SimHub Stepper Belt Tensioner, Sim Belt Tensioner Universal Roller, Compact Traction Loss Seat Mover.
Motion & Tactile
Thanos Controller Emergency Stop
Needed fancier E-Stop with hold switch and RGB status LEDs for my Thanos AMC controller and this project was born!
4.5K views
Motion & Tactile
Dayton SAB-1060 Sim Amp Enclosure
The Dayton Audio SAB-1060 SIM 7.3-Channel Sim Racer / Arcade Amplifier Board is great device, a must we would say for immersive tactile sim build with its 10x60W channels.
3.9K views
Motion & Tactile
SimHub Stepper Belt Tensioner
The original SimHub Design was reworked to look a little better by Mark T to look a little sleeker and then was passed onto me.
23K views1.4K downloads
Motion & Tactile
Sim Belt Tensioner Universal Roller
Universal Roller for Belt Tensioner system. Has two styles for bearing holders - mounting holes inside/outside. Roller can be extended in slices to fit your seat belt guides.
22K views968 downloads
Motion & Tactile
Compact Traction Loss Seat Mover
Use those blocks only as the top-front HGW block mounts. They have only 1mm layers shared between the 4 screws holding the assembly together so they are not as strung as the Heavy Duty ones!
11K views512 downloads
Motion & Tactile
PSU Control Box for Servo Belt Tensioner
Simple enclosure to contain the controlling board (Arduino Nano) and set of 3 balanced supercapacitors for my Belt Tensioner Servo system.
10K views444 downloads
Motion & Tactile
DC-DC 300W Stepdown Enclosure
Simple box for 300W DC-DC Stepdown converter used in the Robot Servo Belt Tensioner.
8.1K views416 downloads
Motion & Tactile
Universal Pedal Mount for Bass Shakers
Short demo of all my iterations for mounting pedal bass shakers. Current setup is with the Heusinkveld Ultimates and Sim-Lab Inverted Mount.
7.8K views
Motion & Tactile
Dayton Puck T-Slot Mount
Dayton Puck mount for T-Slot Aluminum Extrusions. It allows easy mount to 8040 profile, has extended mounts to clear M6 screw heads.
7.7K views547 downloads
Motion & Tactile
AASD-15A Servo Motor Driver Mount
Simple mount plate for the AASD-15A Servo Motor Driver replacing the original one. Provides interface to mount to 4040/3030 Alu Extrusion Profile using M6 screws.
7.7K views333 downloads
Motion & Tactile
Sim Rig Cable Management for Stepper Drivers
Complicated, fancy guides for routing the excessively long cables of the RS Mega+ stepper Drivers. All cables are to be placed on the static base frame, so everything should be neat and tidy.
7.7K views378 downloads
Motion & Tactile
Linear Actuator for Surge
Compact Linear Table Actuator to be used for the Surge Axis in my upcoming 5DOF motion rig.
6.6K views380 downloads
Motion & Tactile
Bass Shaker Mount 8040
Needed new way to mount my bass shakers to 8040 Aluminum Extrusion Profile on my sim rig and came up with this simple design. It is relatively fast to print and can fit small printer bed.
6.4K views433 downloads
Motion & Tactile
Linear Actuator for Traction Loss
Simple linear table actuator to be used in my Compact Traction Loss Seat Mover Motion sub-system. Based on HGR15 linear rails and SFU2005 lead screw.
6.2K views332 downloads
Motion & Tactile
Power Splitter Junction Box
Simple 3D printed power distribution/junction box to be used with my RS Mega+ motion stepped drivers. Clean cable management solution that allows me to route power cables separate from the motor ones.
5.3K views435 downloads
Motion & Tactile
Seat Side Mount for Bass Shakers
Very simple project to mount full sized bass shakers on the side of virtually any side mounted seat. Using 4040 angle brackets provides enough adjustability as they have longer mounting hole.
5.3K views
Motion & Tactile
Thanos AMC Vertical Mount
Simple mount to attach the Thanos AMC controller vertically/sideway to a 40 series Alu extrusion profiles.
5.1K views363 downloads
Motion & Tactile
Xcite XBS50 Mounting Kit
The new compact Xcite XBS50 bass shakers are great, but are not that easy to mount to alu extrusion profiles of a sim rig. Never fear, I is here!
4.4K views236 downloads
Motion & Tactile
Surge Slider Motion Platform
Surge Slider frame to go on top of my 5780 Ultimate Motion Sim Rig. It will provide top mounted surge system for seat and pedals only, steering wheel will be fixed to lower frame.
3.9K views203 downloads
Motion & Tactile
Audio Terminal Box 5x for Shakers
Simple to print audio terminal box to go with the Dayton SAB-1060 10ch Sim Racing Amp .
3.2K views222 downloads