DIY-SIM
← Guides

57 DIY Pro Pedals MK-II: assembly manual

Assembly guide · 16 Nov 2026

Part of the 57 DIY Pro Pedals MK-II design · parts list

Throttle

57 DIY Pro Pedals MK-II: completed throttle pedal

Complete the base through Step 28. Steps 29–35 add the optional damper. Mechanical assembly only. Controller wiring and pedal-to-rig mounting are separate.

Keep previously fitted parts in place as you move to the next step. Some close-ups omit surrounding parts to expose the joint.

Parts, packs to order and prices: see the parts list.

Download the PDF manual35 steps · revision 2026-11-16
Assembly video▶

Before you start

M8 tap and tap wrench
Tap one end of each 150 mm profile, minimum 16 mm usable thread depth.
Hex keys
Use the correct key for each socket or countersunk head.
Heat-insert installation tool
Fit inserts squarely; allow the plastic to cool before inserting screws.
Temporary bearing press
Long M8 and M6 bolts, two large washers and matching nuts. These are tools, not extra installed hardware.
Check the orientation
Inside washers contact the bearing inner race. Press-fit force goes through the outer ring.
T-nut types
M6: spring-loaded roll-in. M8: heavy-duty sliding T-nuts; insert these before closing the profile end.
Screw lengths
Socket bolts are measured under the head. Countersunk screws are measured including the head. Use the JDM washer/screw sets as supplied.

Hardware reference

M8 socket: 16 / 50 / 100 mm
3 x 16 mm: bottom pivot and spring-pivot arms. 1 x 50 mm: pedal axle. 1 x 100 mm: spring rod.
M6 socket: 12 / 16 / 30 mm
2 x 12 mm: rear spring pivot. 5 x 16 mm: three load-cell block, travel stop, damper upper pivot. 1 x 30 mm: damper lower pivot.
M6 countersunk
JDM washer/screw sets at side plates, face mount and LC covers. Two 20 mm screws secure the pedal face.
M3 screws
16 mm for the LC side plates and front spring block. 14 mm countersunk for both damper pivots.
M4 countersunk: 10 mm
Eight screws secure the two load-cell blocks.
Heat inserts
M3: 6 mm long. M6: 7 mm long. M8: 8 mm long.
Bearings and shims
608ZZ: 8 x 22 x 7 mm. 696ZZ: 6 x 15 x 5 mm. Rear spring shims: one 1 mm per side. Damper: three shims above and one below.

Step 01

Prepare the two aluminium profiles

  • 2 x 3030 profiles, 150 mm
  • M8 tap
  1. Use two 3030 aluminium profiles, both 150 mm long. Tap the centre hole at ONE end of each profile with M8 thread.
  2. Minimum usable thread depth: 16 mm. Deburr the ends and remove swarf before assembly.
Two 150 mm 3030 profiles; M8 thread at one end only
Two 150 mm 3030 profiles; M8 thread at one end only

Step 02

Mount the bottom pivot

  • Bottom pivot
  • 1 x M8 x 16 socket bolt
  1. Fit the locating tabs into the profile slots, with the rounded pivot end facing outward. Secure with one M8 x 16 mm socket bolt. No washer is used here.
Fit the pivot to the threaded profile end
Fit the pivot to the threaded profile end

Step 03

Fit the main pivot bearings

  • 2 x 608ZZ
  • Bearing spacer
  • Temporary M8 press tools
  1. Fit two 608ZZ bearings with the spacer between their inner races.
  2. Temporary press: a sufficiently threaded M8 bolt, two large washers and an M8 nut. Apply pressure evenly through the bearing outer rings. Remove the tool after pressing.
Place the spacer between the bearings
Place the spacer between the bearings
Press both bearings squarely into the pivot
Press both bearings squarely into the pivot
Remove the pressing tools
Remove the pressing tools

Step 04

Fit the first base side plate

  • First side plate
  • 2 x M6 roll-in T-nuts
  • 2 x JDM M6 washer/screw sets
  1. Fit two spring-loaded M6 roll-in T-nuts in the lower profile. Orient their threaded holes toward the plate.
  2. Keep the plate upright in its final orientation and secure it with two JDM M6 washer/screw sets.
Fit the two washer and countersunk-screw sets
Fit the two washer and countersunk-screw sets
Align the plate with two M6 roll-in T-nuts
Align the plate with two M6 roll-in T-nuts

Step 05

Fit the opposite base side plate

  • Opposite side plate
  • 2 x M6 roll-in T-nuts
  • 2 x JDM M6 washer/screw sets
  1. Rotate the assembly to access the other side. Fit the second plate with two more M6 roll-in T-nuts and two JDM M6 washer/screw sets.
Rotate the base assembly
Rotate the base assembly
Fit the second plate in the same way
Fit the second plate in the same way
Both plates mounted
Both plates mounted

Step 06

Install the pedal arm

  • Pedal arm
  • M8 x 50 socket bolt
  • 2 x M8 washers
  • M8 locknut
  1. Axle order: M8 x 50 socket bolt > side plate > M8 washer > arm bearing assembly > M8 washer > opposite side plate > M8 locknut.
  2. Both washers sit INSIDE the side plates. Tighten securely and check that the arm moves freely.
Lower the prepared arm between the plates
Lower the prepared arm between the plates
Fit the axle and locknut
Fit the axle and locknut

Step 07

Fit the M6 brass heat-set inserts

  • 2 x M6 heat inserts, 7 mm long
  1. Heat-set one M6 insert into each side of the front load-cell block. Keep them square and allow the block to cool.
Fit one M6 insert into each side
Fit one M6 insert into each side
Inserts fitted before the load cell
Inserts fitted before the load cell

Step 08

Assemble the load-cell front block

  • Load cell
  • Front block
  • 4 x M4 x 10 countersunk screws
  1. Slide the load cell into the prepared front block. Secure with four M4 x 10 mm countersunk screws: two from above and two from below.
Slide in the load cell
Slide in the load cell
Fit 4 M4 countersunk screws
Fit 4 M4 countersunk screws
Completed subassembly
Completed subassembly

Step 09

Prepare the rear load-cell block

  • 8 x M3 heat inserts, 6 mm long
  1. Fit four M3 x 6 mm heat inserts into EACH side of the rear load-cell block: eight total. Allow to cool.
Heat-set 4 inserts into each side
Heat-set 4 inserts into each side
All 8 inserts fitted
All 8 inserts fitted

Step 10

Fit the rear block to the load cell

  • Rear LC block
  • 4 x M4 x 10 countersunk screws
  1. Slide the rear block onto the opposite end of the load cell, with its eight M3 inserts already fitted. Secure with four M4 x 10 mm countersunk screws.
Slide on the prepared rear block
Slide on the prepared rear block
Fit 4 M4 countersunk screws
Fit 4 M4 countersunk screws
Completed load-cell subassembly
Completed load-cell subassembly

Step 11

Fit the load-cell side-plate bearings

  • 2 x 696ZZ bearings
  • Temporary M6 press tools
  1. Press both 696ZZ bearings into the inner faces of the load-cell side plates until FLUSH. The illustrated plates are mirrored, with one logo face shown.
  2. Use a longer M6 bolt, two large washers and an M6 nut as a temporary press. Press squarely on the bearing outer ring, then remove the tools.
Bearings enter from the inside
Bearings enter from the inside
Press-fit; repeat for the other plate
Press-fit; repeat for the other plate
Remove all pressing tools
Remove all pressing tools

Step 12

Mount the load-cell side plates

  • 2 prepared LC side plates
  • 8 x M3 x 16 screws
  1. Mount both prepared plates to the rear load-cell block with four M3 x 16 mm screws per side. Logos face outward.
Align both prepared side plates
Align both prepared side plates
Fit four M3 screws per side
Fit four M3 screws per side
Both plates secured
Both plates secured

Step 13

Mount the load-cell assembly on the base profile

  • 1 x M6 x 16 socket bolt
  • 1 x M6 roll-in T-nut
  1. Fit an M6 spring-loaded roll-in T-nut in the top slot of the base profile, threaded hole upward. Mount the front load-cell block with one M6 x 16 mm socket bolt.
Fit an M6 roll-in T-nut
Fit an M6 roll-in T-nut
Align the assembly and M6 bolt
Align the assembly and M6 bolt
Secure the assembly
Secure the assembly

Step 14

Prepare the front spring block

  • 4 x M3 x 6 heat inserts
  • 1 x M8 heat insert, 8 mm long
  1. Fit four M3 x 6 mm heat inserts, two per side of the front spring block. Fit the M8 x 8 mm insert from the front. Allow to cool.
Heat-set the five brass inserts
Heat-set the five brass inserts
Prepared front spring block
Prepared front spring block

Step 15

Fit the spring-pivot arm bearings

    Bearings enter from the inside
    Bearings enter from the inside
    Press-fit; repeat for the other arm
    Press-fit; repeat for the other arm
    Bearings seated flush; tools removed
    Bearings seated flush; tools removed

    Step 16

    Mount the front spring block between the pivot arms

    • Front spring block
    • 2 pivot arms
    • 4 x M3 x 16 screws
    1. Mount the front spring block between the prepared pivot arms using four M3 x 16 mm screws, two per side. Keep the arms facing right as shown.
    Align the block and prepared arms
    Align the block and prepared arms
    Fit two M3 screws per side
    Fit two M3 screws per side
    Completed spring-pivot subassembly
    Completed spring-pivot subassembly

    Step 17

    Slide the spring pivot onto the pedal arm

    • 2 x M8 x 16 socket bolts
    • 2 x M8 washers
    • 2 x heavy-duty M8 T-nuts
    1. Fit one M8 x 16 socket bolt from outside each bearing. Place one M8 washer on the INSIDE, between the bearing inner race and profile.
    2. Half-thread each HEAVY-DUTY M8 T-nut onto its bolt. Slide both T-nuts into the arm slots from the open end, position the pivot, then tighten.
    Prepare the bolts, inner washers and T-nuts
    Prepare the bolts, inner washers and T-nuts
    Slide the assembly into the pedal-arm slots
    Slide the assembly into the pedal-arm slots
    Position and secure the assembly
    Position and secure the assembly

    Step 18

    Prepare the rear spring block

    • 2 x M6 heat inserts, 7 mm long
    1. Fit one M6 insert into each side of the rear spring block. Allow to cool.
    Heat-set one M6 insert per side
    Heat-set one M6 insert per side
    Prepared rear spring block
    Prepared rear spring block

    Step 19

    Mount the rear spring block between the load-cell uprights

    • 2 x M6 x 12 socket bolts
    • 2 x M6 shims, 1 mm thick
    1. Position the rear spring block between the load-cell uprights. Fit ONE 1 mm M6 shim on each side, contacting the bearing inner race.
    2. Secure from outside with two M6 x 12 mm socket bolts. A 1.2 mm washer per side is the agreed fallback if 1 mm shims are unavailable. Check free movement.
    Block and one inner shim per side
    Block and one inner shim per side
    Fit the two outside M6 bolts
    Fit the two outside M6 bolts
    Rear spring block mounted
    Rear spring block mounted

    Step 20

    Mount the pedal travel stop

    • Travel stop
    • 1 x M6 roll-in T-nut
    • 1 x M6 x 16 socket bolt
    1. Fit the M6 roll-in T-nut into the base profile. Place the travel stop over it and secure with an M6 x 16 mm socket bolt. The stop sits under the spring.
    T-nut, stop and M6 bolt aligned
    T-nut, stop and M6 bolt aligned
    Seat the stop and insert the bolt
    Seat the stop and insert the bolt
    Travel stop mounted
    Travel stop mounted

    Step 21

    Prepare the spring compression ring

    • Compression ring
    • 1 x M8 locknut
    1. Press-fit the M8 locknut fully into the compression ring hex pocket. The ring will sit in front of the spring.
    Align the M8 lock nut with the pocket
    Align the M8 lock nut with the pocket
    Press-fit the nut into the ring
    Press-fit the nut into the ring

    Step 22

    Install the spring and M8 x 100 mm bolt

    • Spring
    • Prepared compression ring
    • 1 x M8 x 100 socket bolt
    1. Insert the M8 x 100 mm bolt from behind the rear spring block. Place the spring and prepared compression ring between the blocks, with the ring in front of the spring.
    2. Advance the bolt and screw the assembly together. The travel stop is already fitted under the spring.
    Bolt from behind; spring and ring above
    Bolt from behind; spring and ring above
    Place spring and ring; advance the bolt
    Place spring and ring; advance the bolt
    Screw the assembly together
    Screw the assembly together

    Step 23

    Prepare the pedal-face mounting block

    • Pedal-face mount block
    • 6 x M6 heat inserts, 7 mm long
    1. Fit six M6 inserts: two in each side face and two from the back for the pedal-face screws. Allow to cool.
    Heat-set all six M6 inserts
    Heat-set all six M6 inserts
    Prepared pedal-face mount
    Prepared pedal-face mount

    Step 24

    Fit the pedal-face mounting side plates

    • Mount block
    • 2 side plates
    • 4 x JDM M6 washer/screw sets
    1. Fit the two side plates to the prepared mounting block with two JDM M6 washers and countersunk screws per side. Leave the two rear inserts available for the pedal face.
    Align the prepared block and plates
    Align the prepared block and plates
    Fit two JDM washer/screw sets per side
    Fit two JDM washer/screw sets per side
    Completed face-mount subassembly
    Completed face-mount subassembly

    Step 25

    Fit the pedal-face mount onto the pedal arm

    • 4 x M6 roll-in T-nuts
    • 4 x JDM M6 washer/screw sets
    1. Fit two M6 roll-in T-nuts into EACH side of the pedal arm. Slide the prepared pedal-face mount onto the arm. Align and secure with four additional JDM M6 washer/screw sets.
    Fit two M6 T-nuts per side
    Fit two M6 T-nuts per side
    Slide on the prepared face mount
    Slide on the prepared face mount
    Secure with four washer/screw sets
    Secure with four washer/screw sets

    Step 26

    Fit the load-cell cover plates

    • 2 LC covers
    • 2 x M6 roll-in T-nuts
    • 2 washer/screw sets
    • 2 x M6 x 16 socket bolts
    1. Each cover uses a washer and M6 countersunk screw into a roll-in T-nut INSIDE the profile, plus an M6 x 16 mm socket bolt into the load-cell block.
    2. Route the load-cell cable through the gap between the BACK EDGE of the block and the covering protrusion on the smaller, far-side plate. The close-up shows the inner side.
    Fit roll-in T-nuts; align both covers
    Fit roll-in T-nuts; align both covers
    Secure each cover at both points
    Secure each cover at both points
    Close-up: cable gap behind smaller cover
    Close-up: cable gap behind smaller cover

    Step 27

    Fit the profile-end covers

    • 3 profile covers
    • Optional hot glue
    1. Press the two covers WITH T-nut cutouts into the ends of the base profile. Fit the solid cover WITHOUT a cutout or logo at the top of the pedal arm.
    2. If needed, use a small dab of hot glue to hold the covers in place.
    Align the three covers
    Align the three covers
    Press the covers into place
    Press the covers into place

    Step 28

    Mount the pedal face

    • Pedal face
    • 2 x M6 x 20 countersunk screws
    1. Rotate the pedal to the front. Mount the pedal face to its block with two M6 x 20 mm countersunk screws, then tighten evenly.
    Front view: align the pedal face
    Front view: align the pedal face
    Insert the two M6 x 20 mm screws
    Insert the two M6 x 20 mm screws
    Pedal face secured
    Pedal face secured

    The base is complete. The next steps are optional.

    Step 29optional

    Prepare the lower-pivot top cap

    • Lower-pivot top cap
    • 2 x M3 heat inserts, 6 mm long
    1. Fit two M3 x 6 mm brass heat inserts squarely into the lower-pivot top cap. Seat their entry ends flush with the cap face, as shown. Allow to cool.
    Fit the two M3 heat-set inserts
    Fit the two M3 heat-set inserts
    Prepared top cap
    Prepared top cap

    Step 30optional

    Fit the lower-pivot bearing

    • Lower-pivot housing
    • 1 x 696ZZ bearing
    1. Press the 696ZZ bearing squarely into the lower housing. Apply force to the outer ring.
    Align bearing with the lower housing
    Align bearing with the lower housing
    Press-fit the bearing into its seat
    Press-fit the bearing into its seat

    Step 31optional

    Close the lower pivot around the damper

    • Prepared lower-pivot parts
    • Damper
    • 2 x M3 x 14 countersunk screws
    1. Seat the damper end in the lower housing, then fit the prepared top cap.
    2. Insert the two M3 x 14 mm countersunk screws from UNDERNEATH the lower housing. They thread into the top-cap inserts. Tighten evenly.
    Insert the damper end in the housing
    Insert the damper end in the housing
    Fit cap; insert screws from underneath
    Fit cap; insert screws from underneath
    Completed lower-pivot subassembly
    Completed lower-pivot subassembly

    Step 32optional

    Prepare the top pivot

    • Top-pivot block
    • 4 x M3 x 6 inserts
    • 696ZZ bearing
    • Cover
    • 4 x M3 x 14 screws
    1. Fit the four M3 x 6 mm heat inserts and allow to cool. Insert the 696ZZ bearing into its seat.
    2. Fit the cover UNDER the bearing and secure it with four M3 x 14 mm countersunk screws.
    Fit four M3 x 6 mm inserts
    Fit four M3 x 6 mm inserts
    Insert the 696ZZ bearing
    Insert the 696ZZ bearing
    Fit the cover and four M3 x 14 screws
    Fit the cover and four M3 x 14 screws
    Tighten the cover evenly
    Tighten the cover evenly

    Step 33optional

    Mount the top pivot on the pedal arm

    • Prepared top pivot
    • M6 roll-in T-nut
    • 3 M6 shims
    • M6 x 16 socket bolt
    1. Inside to outside: M6 roll-in T-nut INSIDE the arm slot > THREE M6 shims > pivot bearing/block > M6 x 16 mm socket bolt.
    2. Tighten the stack to secure the top-pivot assembly on the pedal arm.
    T-nut > three shims > pivot > M6 x 16 bolt
    T-nut > three shims > pivot > M6 x 16 bolt
    Tighten the mounting bolt
    Tighten the mounting bolt
    Top pivot installed
    Top pivot installed

    Step 34optional

    Thread in the damper and mount the lower pivot

    • Damper + 1 supplied M14 nut
    • Printed spacer
    • M6 shim
    • M6 T-nut
    • M6 x 30 socket bolt
    1. Thread the M14 retention nut onto the damper, leaving it loose halfway along the body. Thread the damper into the top pivot until its lower pivot roughly aligns with the base.
    2. Lower mounting order: roll-in T-nut INSIDE the base slot > printed spacer block > ONE M6 shim > lower-pivot bearing > M6 x 30 mm socket bolt.
    Thread M14 damper into the top pivot
    Thread M14 damper into the top pivot
    Fit the lower mounting stack
    Fit the lower mounting stack
    Secure with M6 x 30 mm socket bolt
    Secure with M6 x 30 mm socket bolt

    Step 35optional

    Final adjustment - throttle assembly complete

    • One M14 retention nut, supplied with the damper
    1. Rotate the damper to obtain its full range without restricting pedal travel. Check the complete pedal stroke.
    2. When satisfied with the position, tighten the M14 retention nut against the top pivot. Your throttle pedal is assembled!
    Rotate damper; check full pedal travel
    Rotate damper; check full pedal travel
    Tighten the M14 retention nut
    Tighten the M14 retention nut
    The design57 DIY Pro Pedals MK-II3D files, parts list and updates →

    More guides